开环运行直流配用电系统安全域模型建立与应用

doi:10.12204/j.issn.1000-7229.2021.07.006

摘要/Abstract

摘要：

根据直流配用电系统安全性要求,针对一组预想故障,系统应具有对负荷持续供电的能力。N-1校验作为系统故障情况下能否持续带载的评判标准,反映了系统安全性的强弱。当前对直流配用电系统安全性研究较少,为了研究故障后系统的转供机理,对开环运行的直流配电系统进行分析,以此建立简化的安全域模型。首先定义N-1校验所需参数,推导各参数之间的数学关系,以期用较少的参数表示出系统的网络架构。在此基础上分析馈线N-1故障及换流站N-1故障的转供机理,利用已定义的参数描述此转供过程,得到了馈线和换流站的N-1约束条件,建立安全域模型。随后基于安全域模型对系统最大供电能力进行求解,推导分析供电能力与负载均衡度之间的关系,绘制最大供电能力-方差曲线,并利用熵权理想度排序法找到最优解。通过算例与现有安全域模型对比校验,验证了所提模型的可行性,为直流配电系统规划、建设、运行和维护提供理论基础。

关键词: 直流配电网, N-1校验, 安全性, 供电能力

Abstract:

The security of the DC distribution system requires the system to maintain the ability to supply power in response to a set of expected faults. N-1 check, which reflects the strength of system security, is used as a criterion for judging whether the system can continue to carry load under the condition of system fault. At present, no corresponding evaluation standard are studied on the security of DC distribution system. In order to study the transfer mechanism of fault sysem, open-loop topology is analyzed to establish a simplified security region model. Firstly, the parameters required by N-1 check are defined, and mathematical relationship between these parameters is derived, which is to reveal the network architecture of the system with fewer parameters. Secondly, the transfer mechanism of feederN-1 fault and converter station N-1 fault is analyzed. According to the defined parameters, the transfer process is described, and the N-1 constraint conditions of the feeders and converter stations are obtained. Therefore, the security region model is established. Thirdly, applying the security region model, the total supply capability of the system is calculated. Also, the relationship between power supply capability and load balance, which can be drawn as C_S-s² curve, is deduced. Thereafter, the optimal solution is found by using the entropy order method to analyze the curve. Finally, the feasibility of the model proposed in this paper is verified by comparing with existing security region model in the example.

Key words: DC distribution network, N-1 check, security, power supply capability

中图分类号:

TM744

孟祥坤, 韩民晓, 张夏辉, 曹文远, 缪惠宇. 开环运行直流配用电系统安全域模型建立与应用[J]. 电力建设, 2021, 42(7): 48-57.

MENG Xiangkun, HAN Minxiao, ZHANG Xiahui, CAO Wenyuan, MIAO Huiyu. Establishment and Application of Security Region Model of DC Distribution System[J]. ELECTRIC POWER CONSTRUCTION, 2021, 42(7): 48-57.

图/表 13

图1 不对称两分段接线

Fig.1 Asymmetric two-section connection mode

表1 不对称两分段接线T、G、L、H矩阵数值

Table 1 Matrix values in asymmetric two-section connection mode

图2 馈线N-1故障转供机理

Fig.2 Transfer mechanism of feeder N-1 fault

图3 m为下级馈线段

Fig.3 Fault on the lower-level feeder

图4 换流站N-1故障转供机理

Fig.4 Transfer mechanism of N-1 fault between converter stations

表A1 典型接线模式

Table A1 Typical connection mode

表A2 典型接线模式安全域模型计算结果

Table A2 Calculation results of security region model in typical connection mode

图5 CS-s2曲线及最优解流程图

Fig.5 Flow chart for CS-s2 curve and optimal solution

图6 配电系统网络架构

Fig.6 Network configuration of the distribution system

表A3 算例计算结果

Table A3 Calculation results of the example

图7 局部馈线网络架构

Fig.7 Part of the network configuration

表2 馈线段1对应A1、A2中部分参数

Table 2 Part of A1、A2 parameters corresponds to feeder 1

图8 CS-s2曲线

Fig.8 CS-s2 curve

参考文献 23

[1]	韩民晓, 谢文强, 曹文远, 等. 中压直流配电网应用场景与系统设计[J]. 电力系统自动化, 2019, 43(23):2-11,89.
	HAN Minxiao, XIE Wenqiang, CAO Wenyuan, et al. Application scenarios and system design of medium-voltage DC distribution network[J]. Automation of Electric Power Systems, 2019, 43(23):2-11,89.
[2]	宋强, 赵彪, 刘文华, 等. 智能直流配电网研究综述[J]. 中国电机工程学报, 2013, 33(25):9-19,5.
	SONG Qiang, ZHAO Biao, LIU Wenhua, et al. An overview of research on smart DC distribution power network[J]. Proceedings of the CSEE, 2013, 33(25):9-19,5.
[3]	江道灼, 郑欢. 直流配电网研究现状与展望[J]. 电力系统自动化, 2012, 36(8):98-104.
	JIANG Daozhuo, ZHENG Huan. Research status and developing prospect of DC distribution network[J]. Automation of Electric Power Systems, 2012, 36(8):98-104.
[4]	曹文远, 韩民晓, 谢文强, 等. 交直流配电网逆变器并联控制技术研究现状分析[J]. 电工技术学报, 2019, 34(20):4226-4241.
	CAO Wenyuan, HAN Minxiao, XIE Wenqiang, et al. Analysis on research status of parallel inverters control technologies for AC/DC distribution network[J]. Transactions of China Electrotechnical Society, 2019, 34(20):4226-4241.
[5]	王成山, 罗凤章. 配电系统综合评价理论与方法[M]. 北京: 科学出版社, 2012.
[6]	刘伟, 郭志忠. 配电网安全性指标的研究[J]. 中国电机工程学报, 2003, 23(8):85-90.
	LIU Wei, GUO Zhizhong. Research on security indices of distribution networks[J]. Proceedings of the CSEE, 2003, 23(8):85-90.
[7]	刘若溪, 张建华, 吴迪. 基于风险理论的配电网静态安全性评估指标研究[J]. 电力系统保护与控制, 2011, 39(15):89-95.
	LIU Ruoxi, ZHANG Jianhua, WU Di. Research on static security index of distribution network based on risk theory[J]. Power System Protection and Control, 2011, 39(15):89-95.
[8]	谢红卉, 毛建林. 配电网安全性评价指标与方法研究[J]. 电气技术, 2011(10):39-41.
	XIE Honghui, MAO Jianlin. Research on security indices and method of distribution networks[J]. Electrical Engineering, 2011(10):39-41.
[9]	梁丁相, 陈曦. 基于模糊综合评判理论的电力信息系统安全风险评估模型及应用[J]. 电力系统保护与控制, 2009, 37(5):61-64.
	LIANG Dingxiang, CHEN Xi. Safety assessment model of electric power information system based on fuzzing synthetical theory and its application[J]. Power System Protection and Control, 2009, 37(5):61-64.
[10]	朱嘉麒, 董树锋, 徐成司, 等. 考虑多次转供的配电网最大供电能力评估方法[J]. 电网技术, 2019, 43(7):2275-2282.
	ZHU Jiaqi, DONG Shufeng, XU Chengsi, et al. Evaluation model of total supply capability of distribution network considering multiple transfers[J]. Power System Technology, 2019, 43(7):2275-2282.
[11]	CHEN K N, WU W C, ZHANG B M, et al. A method to evaluate total supply capability of distribution systems considering network reconfiguration and daily load curves[J]. IEEE Transactions on Power Systems, 2016, 31(3):2096-2104. doi: 10.1109/TPWRS.2015.2444792 URL
[12]	肖峻, 屈玉清, 宋晨辉, 等. 城市配电网正常运行约束安全域及最大供电能力的网络流本质[J]. 电网技术, 2020, 44(11):4368-4376.
	XIAO Jun, QU Yuqing, SONG Chenhui, et al. The network flow nature of security region and total supply capability for urban distribution network with normal operation constraints[J]. Power System Technology, 2020, 44(11):4368-4376.
[13]	肖峻, 谷文卓, 郭晓丹, 等. 配电系统供电能力模型[J]. 电力系统自动化, 2011, 35(24):47-52.
	XIAO Jun, GU Wenzhuo, GUO Xiaodan, et al. A supply capability model for distribution systems[J]. Automation of Electric Power Systems, 2011, 35(24):47-52.
[14]	王成山, 罗凤章, 肖峻, 等. 基于主变互联关系的配电系统供电能力计算方法[J]. 中国电机工程学报, 2009, 29(13):86-91.
	WANG Chengshan, LUO Fengzhang, XIAO Jun, et al. An evaluation method for power supply capability of distribution system based on analyzing interconnections of main transformers[J]. Proceedings of the CSEE, 2009, 29(13):86-91.
[15]	肖峻, 谷文卓, 贡晓旭, 等. 基于馈线互联关系的配电网最大供电能力模型[J]. 电力系统自动化, 2013, 37(17):72-77.
	XIAO Jun, GU Wenzhuo, GONG Xiaoxu, et al. A total supply capability model for power distribution network based on feeders interconnection[J]. Automation of Electric Power Systems, 2013, 37(17):72-77.
[16]	肖峻, 贡晓旭, 王成山. 配电网最大供电能力与N-1安全校验的对比验证[J]. 电力系统自动化, 2012, 36(18):86-91.
	XIAO Jun, GONG Xiaoxu, WANG Chengshan. Comparative research between total supply capability and N-1 security verification for distribution networks [J]. Automation of Electric Power Systems, 2012, 36(18):86-91.
[17]	XIAO J, GU W, WANG C, et al. Distribution system security region: Definition, model and security assessment[J]. IET Generation, Transmission & Distribution, 2012, 6(10):1029. doi: 10.1049/iet-gtd.2011.0767 URL
[18]	肖峻, 苏步芸, 贡晓旭, 等. 基于馈线互联关系的配电网安全域模型[J]. 电力系统保护与控制, 2015, 43(20):36-44.
	XIAO Jun, SU Buyun, GONG Xiaoxu, et al. Model of distribution system security region based on interconnections of feeders[J]. Power System Protection and Control, 2015, 43(20):36-44.
[19]	肖峻, 张婷, 张跃, 等. 基于最大供电能力的配电网规划理念与方法[J]. 中国电机工程学报, 2013, 33(10):106-113.
	XIAO Jun, ZHANG Ting, ZHANG Yue, et al. TSC-based planning idea and method for distribution networks[J]. Proceedings of the CSEE, 2013, 33(10):106-113.
[20]	王正平, 赵倩宇, 禚程程, 等. 直流配电系统拓扑结构及其在工程示范中的应用[J]. 供用电, 2020, 37(5):31-35.
	WANG Zhengping, ZHAO Qianyu, ZHUO Chengcheng, et al. Topological structure of DC distribution system and its application in demonstration projects[J]. Distribution & Utilization, 2020, 37(5):31-35.
[21]	苏麟, 朱鹏飞, 闫安心, 等. 苏州中压直流配电工程设计方案及仿真验证[J]. 中国电力, 2021, 54(1):78-88.
	SU Lin, ZHU Pengfei, YAN Anxin, et al. Design scheme and simulation verification of Suzhou medium voltage DC distribution project[J]. Electric Power, 2021, 54(1):78-88.
[22]	肖峻, 曹严, 张宝强, 等. 配电网安全域的全维直接观测[J]. 电工技术学报, 2020, 35(19):4171-4182.
	XIAO Jun, CAO Yan, ZHANG Baoqiang, et al. Full-dimensional direct observation of distribution system security region[J]. Transactions of China Electrotechnical Society, 2020, 35(19):4171-4182.
[23]	荆朝霞, 王宏益, 江昌旭. 考虑负荷均衡的220 kV电网供电能力多目标优化[J]. 电网技术, 2017, 41(5):1619-1628.
	JING Zhaoxia, WANG Hongyi, JIANG Changxu. Multi-objective optimization of power supply capability of 220 kV power grid concerning load balance[J]. Power System Technology, 2017, 41(5):1619-1628.